yes, because she is only the head, but caps them good luck!
I used cotton Snappy Ball Adriafil are gomitoloni of 200 g. but I think they are enough 50 or so, depends on the hand and a hook for cotton (as steel) No 2
Snappy Ball Adriafil
crocheted No 2
Points used:
chain, mesh very low, treble, treble in relief (ribs)
Run method 1:
1st round: in a ring formed by the end of the wire work 6 m high separated by a chain, replacing the first treble and the first chain with 4 chains
2 ° lap 4 m high chain-1 in the same basic m -1 chain-2 m high, separated by a cat and a cat on each of the following m high. 1 m low in the third cat start
3rd round: 4 cat-1 m high on the same high m - 1 -1 m high cat 1 cat on the next higher-m * 2 m high from sep 1 cat and a cat on m-1 m high of trouble free a cat on the following m * repeat from * to * all around the low m-1 on third lap cat
start from 4th on lap 16: Work 2 m high from a cat on sep but the first group of the previous lap, but a 1 m high on every single cat in the previous round.
17 ° 18 ° 19 ° around: Always start with 4 cat-1 cat 1 m high on each of the g m high above. Always end m with a low start in the third cat
around lap 20: 2-point crochet cat in the 2nd m high make a high m not closed, a cast and close all sull'uncinetto 1 m-1 m chain cat on a high following 6 m high cat-1 * 2 m high closed with a cat on the 2 m high following a cat * - repeat from * to * all around
21 ° 22 ° 23 ° around 2 m high closed cat ass 1 m high on each enclosed with the previous lap-1 m high cat 1 m high on each
lap 24: 3 cat-1 m high on each m high and 1 m high in the space of a cat in the previous round.
25 ° 26 ° 27 ° 28 ° around a beaded mesh to form the effect of the ribs 2 / 2: start each round with 1 m low by introducing the hook, straight from the other side, in the space between the last m high and the first passing under the first and leave the space between the first and second m high cat-2 - 1 m high in the Similarly-1 m high by introducing the hook from back to the right, in the space between the second and third m high of the previous lap, passing over the m high and return on the back, end the treble .- make an equal the following m - m to a high intake below (as before) on each of two successive m-1 m high and taken from under 2 m high on each of the following throughout the round - to finish with a low m on the second chain
beginning around lap 29: as previous but low in meshes.
Cut and stop the wires.
2 ° method:
1st round: in a ring formed by the end of the wire work and a chain 6 m low - pull the ends of the wire to tighten the ring and close the round with a low in the first m m low starting around
2nd round: 4 chains (= 1 + 1 m high chain) - 1 m high 1 m in the same chain base from which the four chains - 2 m high da1 a separate chain and a chain on following 5 m low - close around 1 m with very low on the 3rd beginning chain around.
lap 3 and the following as the method 1
The difference between the two methods is that with the second is flatter than the beginning of the cap and does not hump.
I've done it! He did not want to publish and so I tried to make a separate page below. That came on the first try .... Mysteries of information .....
0 comments:
Post a Comment